| Redisplay Messages: Compact | Brief | All | Full Show Messages: All | Without Replies Author: | Thargor | Posted: | Mar 24, 2021 04:44 | Subject: | Minifigure sw0737a | Viewed: | 102 times | Topic: | Catalog | Status: | Open | |
|
| I just saw that Minifigure sw0737a Poe Dameron was added to the catalog. This
Minifigure is included in set 75149 and comes with helmet and hair piece.
In the past we often had Minifigures that had both helmet and hair piece but
they were only listed once in the catalog e.g. sw0416, sw0772, sw0407 ...
Why is Poe now listed twice as sw0737 with hair and as sw0737a with helmet?
|
|
Author: | randyf | Posted: | Mar 23, 2021 20:08 | Subject: | Re: 3003pb004 sticker too large | Viewed: | 40 times | Topic: | Catalog | |
|
| In Catalog, normann1974 writes:
| In Catalog, normann1974 writes:
Well, we know that there is no (official) correct way to apply the sticker because
the instructions don't show the sticker size correctly.
So now that I'm thinking of it, I'm not sure that we can conclude that
this sticker should be applied to two 2x2 bricks the way it was done on the part
I found (that I now created as a stickered assembly in the catalog).
The sticker could also be applied to one 2x2 brick and the printed tile on top
of the brick, or maybe on all three parts together. So maybe assemblies for those
two variations also should be created if someone has them. Thoughts?
/Jan
|
The 4 black circles are clearly on the 2x2 brick, so I think the way it is now
is how it should be.
|
|
Author: | normann1974 | Posted: | Mar 23, 2021 19:58 | Subject: | Re: 3003pb004 sticker too large | Viewed: | 32 times | Topic: | Catalog | |
|
| In Catalog, normann1974 writes:
Well, we know that there is no (official) correct way to apply the sticker because
the instructions don't show the sticker size correctly.
So now that I'm thinking of it, I'm not sure that we can conclude that
this sticker should be applied to two 2x2 bricks the way it was done on the part
I found (that I now created as a stickered assembly in the catalog).
The sticker could also be applied to one 2x2 brick and the printed tile on top
of the brick, or maybe on all three parts together. So maybe assemblies for those
two variations also should be created if someone has them. Thoughts?
/Jan
|
|
Author: | normann1974 | Posted: | Mar 23, 2021 18:49 | Subject: | Re: 3003pb004 sticker too large | Viewed: | 31 times | Topic: | Catalog | |
|
| has now been added.
/Jan
|
|
Author: | paulvdb | Posted: | Mar 23, 2021 00:46 | Subject: | Re: 3003pb004 sticker too large | Viewed: | 29 times | Topic: | Catalog | |
|
| I checked my own set and can confirm that the sticker is too big to fit on one
brick, so the current catalog entry for this stickered counterpart should be
replaced by a stickered assembly.
In Catalog Requests, patpendlego writes:
| The instructions are just a drawing, that does not prove anything.
Clearly the sticker on the stickersheet is larger than the side of a 2x2 brick,
so it does not fit on 1 brick and should be placed on 2 bricks. The stove is
2 bricks high so that is very well possible.
IMO the entry with the sticker on 1 brick is wrong, it should be an assembly
with 2 bricks.
In Catalog Requests, starbeanie writes:
| http://www.peeron.com/scans/6365-1/4/
In Catalog Requests, starbeanie writes:
| I think the bottom of yours just didn't get the diecut right. Notice how
the print extends down past the black line. If you look at the instructions,
it fits a single brick.
In Catalog Requests, normann1974 writes:
| I'm sitting with something that looks like part in my hands.
The sticker on these bricks is clearly too large to fit on one brick. So does
this sticker exist in different sizes or is the current part image showing a
cut sticker? Should this part be retired and an assembly be made instead?
Note that I've found parts [P=3068bp65] and in the same lot
of bricks, so I'd say there's virtually no chance that the stove sticker
didn't come from set .
/Jan
|
|
|
|
|
|
Next Page: 5 More | 10 More | 25 More | 50 More | 100 More
|
|