| Redisplay Messages: Compact | Brief | All | Full Show Messages: All | Without Replies Author: | BricksThatStick | Posted: | Mar 21, 2020 19:46 | Subject: | Re: Wheel plate stuck on car chassis piece | Viewed: | 43 times | Topic: | Catalog | |
|
| In Catalog, crazylegoman writes:
| In Catalog, BricksThatStick writes:
| In Catalog, SylvainLS writes:
| In Catalog, randyf writes:
| In Catalog, crazylegoman writes:
| Does anyone know if
is meant to be able to be removed from
* | | 11650c01 Vehicle, Base 5 x 10 x 2 1/2 with Mudguards and 6 x 2 Recessed Center with 3 Holes with (Same Color) Wheels Holders Attached Parts: Vehicle, Base |
once they are together?
|
The whole vehicle base is one part. Nothing on it is meant to come off.
|
Sure?
LDraw has the part (11650.dat) without the plates with wheel pins and the part
with the plates exist in two versions: 12622.dat in one colour and 12622p01.dat
with LBG plates.
Are those some sort of rivets?
Or do they use a special technique to connect the plates?
| | I feel like the axles are going to snap off of the 2X2 plates if I pull any herder
than I already am. Also, I've never seen a post with a tapered part at the
end like the chassis piece has. It seems a bit like those Bionicle brains and
heads.
David
|
|
|
The pin that holds them on clips through and then can't be reversed - see
pic
|
That's the same as what I have, except in different colors. Do you know
if they come already assembled in the box? (The one I have is from a used lot.)
randyf, the part is definitely made up of 3 separate parts (1 of the main chassis,
and 2 of the modified 2X2 plates.) Each of the 3 parts has a molded part number
that you can see on the underside.
David
|
This set review has both the red and LBG holders:
https://youtu.be/cIeqTh0x82g
|
|
|
Author: | crazylegoman | Posted: | Mar 21, 2020 19:28 | Subject: | Re: Wheel plate stuck on car chassis piece | Viewed: | 38 times | Topic: | Catalog | |
|
| In Catalog, BricksThatStick writes:
| In Catalog, SylvainLS writes:
| In Catalog, randyf writes:
| In Catalog, crazylegoman writes:
| Does anyone know if
is meant to be able to be removed from
* | | 11650c01 Vehicle, Base 5 x 10 x 2 1/2 with Mudguards and 6 x 2 Recessed Center with 3 Holes with (Same Color) Wheels Holders Attached Parts: Vehicle, Base |
once they are together?
|
The whole vehicle base is one part. Nothing on it is meant to come off.
|
Sure?
LDraw has the part (11650.dat) without the plates with wheel pins and the part
with the plates exist in two versions: 12622.dat in one colour and 12622p01.dat
with LBG plates.
Are those some sort of rivets?
Or do they use a special technique to connect the plates?
| | I feel like the axles are going to snap off of the 2X2 plates if I pull any herder
than I already am. Also, I've never seen a post with a tapered part at the
end like the chassis piece has. It seems a bit like those Bionicle brains and
heads.
David
|
|
|
The pin that holds them on clips through and then can't be reversed - see
pic
|
That's the same as what I have, except in different colors. Do you know
if they come already assembled in the box? (The one I have is from a used lot.)
randyf, the part is definitely made up of 3 separate parts (1 of the main chassis,
and 2 of the modified 2X2 plates.) Each of the 3 parts has a molded part number
that you can see on the underside.
David
|
|
|
Author: | BricksThatStick | Posted: | Mar 21, 2020 18:47 | Subject: | Re: Wheel plate stuck on car chassis piece | Viewed: | 45 times | Topic: | Catalog | |
|
| In Catalog, SylvainLS writes:
| In Catalog, randyf writes:
| In Catalog, crazylegoman writes:
| Does anyone know if
is meant to be able to be removed from
* | | 11650c01 Vehicle, Base 5 x 10 x 2 1/2 with Mudguards and 6 x 2 Recessed Center with 3 Holes with (Same Color) Wheels Holders Attached Parts: Vehicle, Base |
once they are together?
|
The whole vehicle base is one part. Nothing on it is meant to come off.
|
Sure?
LDraw has the part (11650.dat) without the plates with wheel pins and the part
with the plates exist in two versions: 12622.dat in one colour and 12622p01.dat
with LBG plates.
Are those some sort of rivets?
Or do they use a special technique to connect the plates?
| | I feel like the axles are going to snap off of the 2X2 plates if I pull any herder
than I already am. Also, I've never seen a post with a tapered part at the
end like the chassis piece has. It seems a bit like those Bionicle brains and
heads.
David
|
|
|
The pin that holds them on clips through and then can't be reversed - see
pic
|
|
|
Author: | SylvainLS | Posted: | Mar 21, 2020 17:11 | Subject: | Re: Wheel plate stuck on car chassis piece | Viewed: | 37 times | Topic: | Catalog | |
|
| In Catalog, randyf writes:
| In Catalog, crazylegoman writes:
| Does anyone know if
is meant to be able to be removed from
* | | 11650c01 Vehicle, Base 5 x 10 x 2 1/2 with Mudguards and 6 x 2 Recessed Center with 3 Holes with (Same Color) Wheels Holders Attached Parts: Vehicle, Base |
once they are together?
|
The whole vehicle base is one part. Nothing on it is meant to come off.
|
Sure?
LDraw has the part (11650.dat) without the plates with wheel pins and the part
with the plates exist in two versions: 12622.dat in one colour and 12622p01.dat
with LBG plates.
Are those some sort of rivets?
Or do they use a special technique to connect the plates?
| | I feel like the axles are going to snap off of the 2X2 plates if I pull any herder
than I already am. Also, I've never seen a post with a tapered part at the
end like the chassis piece has. It seems a bit like those Bionicle brains and
heads.
David
|
|
|
|
Next Page: 5 More | 10 More | 25 More | 50 More | 100 More
|
|