Discussion Forum: Thread 234486 |
|
|
| | Author: | normann1974 | Posted: | Apr 1, 2018 16:08 | Subject: | Inventory Change Request for Set 7749-1 | Viewed: | 33 times | Topic: | Inventories Requests (Entry) | Status: | Open | |
|
| Please make changes to the following inventory:
* Change {2 to 1} Part Black 48729b Bar 1L with Clip Mechanical Claw, Cut Edges and Hole on Side (Alternate)
Comments from Submitter:
Judging by other sets (e.g. 10197-1), the alternate count must match the regular count, not the sum of regular and extras.
|
|
| | | | | |
| | | | Author: | Hygrotus | Posted: | Apr 2, 2018 17:39 | Subject: | Re: Inventory Change Request for Set 7749-1 | Viewed: | 21 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, normann1974 writes:
| Please make changes to the following inventory:
* Change {2 to 1} Part Black 48729b Bar 1L with Clip Mechanical Claw, Cut Edges and Hole on Side (Alternate)
Comments from Submitter:
Judging by other sets (e.g. 10197-1), the alternate count must match the regular count, not the sum of regular and extras.
|
There were different approach to deal with alternate to extras. See also this
tread https://www.bricklink.com/message.asp?ID=1066533. I adjusted it as in this
set for example I think this is the best way to deal with this problem.
Marek
|
|
|
| | | | | | | | | |
| | | | | | Author: | normann1974 | Posted: | Apr 2, 2018 19:15 | Subject: | Re: Inventory Change Request for Set 7749-1 | Viewed: | 24 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Hygrotus writes:
| In Inventories Requests, normann1974 writes:
| Please make changes to the following inventory:
* Change {2 to 1} Part Black 48729b Bar 1L with Clip Mechanical Claw, Cut Edges and Hole on Side (Alternate)
Comments from Submitter:
Judging by other sets (e.g. 10197-1), the alternate count must match the regular count, not the sum of regular and extras.
|
There were different approach to deal with alternate to extras. See also this
tread https://www.bricklink.com/message.asp?ID=1066533. I adjusted it as in this
set for example I think this is the best way to deal with this problem.
Marek
|
I remember that discussion now. I was part of it, but I don't remember any
final decision was ever made. Only a suggestion to management.
So is your suggestion here (which is the same as in the other thread, and which
I think is good) the correct to handle the situation for the time being, i.e.
should I update any inventories that don't follow this pattern? It's
probably many.
/Jan
|
|
|
| | | | | | | | | | | | | |
| | | | | | | | Author: | Admin_Russell | Posted: | Apr 2, 2018 19:21 | Subject: | Re: Inventory Change Request for Set 7749-1 | Viewed: | 34 times | Topic: | Inventories Requests | |
|
|
BrickLink ID CardAdmin_Russell
|
Location: USA, California |
Member Since |
Contact |
Type |
Status |
May 9, 2017 |
|
Admin |
|
|
BrickLink Administrator |
|
| In Inventories Requests, normann1974 writes:
| In Inventories Requests, Hygrotus writes:
| In Inventories Requests, normann1974 writes:
| Please make changes to the following inventory:
* Change {2 to 1} Part Black 48729b Bar 1L with Clip Mechanical Claw, Cut Edges and Hole on Side (Alternate)
Comments from Submitter:
Judging by other sets (e.g. 10197-1), the alternate count must match the regular count, not the sum of regular and extras.
|
There were different approach to deal with alternate to extras. See also this
tread https://www.bricklink.com/message.asp?ID=1066533. I adjusted it as in this
set for example I think this is the best way to deal with this problem.
Marek
|
I remember that discussion now. I was part of it, but I don't remember any
final decision was ever made. Only a suggestion to management.
So is your suggestion here (which is the same as in the other thread, and which
I think is good) the correct to handle the situation for the time being, i.e.
should I update any inventories that don't follow this pattern? It's
probably many.
/Jan
|
Unless the inventory is too complicated. Like the Death Star:
|
|
|
|
|
|
|