| Redisplay Messages: Compact | Brief | All | Full Show Messages: All | Without Replies Author: | normann1974 | Posted: | May 28, 2021 19:44 | Subject: | Inventory Change Request for Set 4916-1 | Viewed: | 15 times | Topic: | Inventories Requests (Entry) | Status: | Open | |
|
| Please make changes to the following inventory:
* Change 1 Part Dark Bluish Gray {44567 Hinge Plate 1 x 2 Locking with 1 Finger on Side (Undetermined Type) to 44567a Hinge Plate 1 x 2 Locking with 1 Finger on Side with Bottom Groove}
* Change 4 Part Dark Bluish Gray {44302 Hinge Plate 1 x 2 Locking with 2 Fingers on End (Undetermined Type) to 44302a Hinge Plate 1 x 2 Locking with 2 Fingers on End and 9 Teeth with Bottom Groove}
* Change 1 Part Dark Bluish Gray {44301 Hinge Plate 1 x 2 Locking with 1 Finger On End (Undetermined Type) to 44301a Hinge Plate 1 x 2 Locking with 1 Finger On End with Bottom Groove}
Comments from Submitter:
I just parted out this set.
|
|
Author: | normann1974 | Posted: | May 28, 2021 19:26 | Subject: | Inventory Change Request for Set 4838-1 | Viewed: | 20 times | Topic: | Inventories Requests (Entry) | Status: | Open | |
|
| Please make changes to the following inventory:
* Add 2 Part 4589b Light Bluish Gray Cone 1 x 1 with Top Groove (Alternate) (match ID 1)
* Add 1 Part 54200 Light Bluish Gray Slope 30 1 x 1 x 2/3 (Extra)
* Add 1 Part 54200 Orange Slope 30 1 x 1 x 2/3 (Extra)
* Add 1 Part 54200 White Slope 30 1 x 1 x 2/3 (Extra)
* Add 1 Part 54200 Trans-Yellow Slope 30 1 x 1 x 2/3 (Extra)
* Change 2 Part Light Bluish Gray 4589 Cone 1 x 1 without Top Groove {match ID 0 to 1}
* Change 2 Part White {4623 Plate, Modified 1 x 2 with Bar Arm Up (Undetermined Horizontal Arm Length) to 4623a Plate, Modified 1 x 2 with Bar Arm Up (Horizontal Arm 6mm)}
Comments from Submitter:
I just parted out this set.
|
|
Author: | normann1974 | Posted: | May 23, 2021 17:20 | Subject: | Re: Inventory re-confirmation | Viewed: | 32 times | Topic: | Suggestions | |
|
| In Suggestions, Turez writes:
| In Suggestions, normann1974 writes:
| I currently can't confirm an inventory more than once. It would be nice to
be able to confirm an inventory again if changes were made since the last confirmation
so I'm able to confirm the inventory with the changes. For instance I have
previously confirmed
before part was split. I would like to confirm that the change
to is correct but I can't.
/Jan
|
I can remove your confirmation so you can confirm it again. Do you want me to
do that?
I think this is better than to wait for an option to confirm an inventory several
times (which could also look a bit strange).
|
Yes, you may do that.
/Jan
|
|
Author: | normann1974 | Posted: | May 23, 2021 16:18 | Subject: | Inventory re-confirmation | Viewed: | 102 times | Topic: | Suggestions | Status: | Already Exists | |
|
| I currently can't confirm an inventory more than once. It would be nice to
be able to confirm an inventory again if changes were made since the last confirmation
so I'm able to confirm the inventory with the changes. For instance I have
previously confirmed
before part was split. I would like to confirm that the change
to is correct but I can't.
/Jan
|
|
Author: | normann1974 | Posted: | May 20, 2021 17:17 | Subject: | Re: Add co-brand | Viewed: | 22 times | Topic: | Catalog Requests | |
|
| | I think the images from the instructions are fine, so there is no need to keep
trying to find something else. There are many other promotional sets that use
line-drawn renders from instructions.
|
Ok, I have uploaded the only good photo I was able to obtain of the 6 sets. At
this point I don't have any more information, I'm just awaiting the last
5 inventories to be accepted.
/Jan
|
Next Page: 5 More | 10 More | 25 More | 50 More | 100 More
|
|