| Redisplay Messages: Compact | Brief | All | Full Show Messages: All | Without Replies Author: | randyf | Posted: | Mar 31, 2021 16:26 | Subject: | Re: Dimensions of tires | Viewed: | 40 times | Topic: | Catalog | |
|
| In Catalog, cosmicray writes:
| I would like to provide a Catalog dimension for
Plus the various part assemblies that include that tire. The change page suggests
that the numbers are in studs. Is this correct, or should I be entering in cm
?
According to my caliper the tire really does measure 30 x 30 x 14 mm.
When entering the dimensions for the assemblies, do I do that with the wheel
inserted in the tire, or with them side by side ? example
Nita Rae
|
It sounds like you are measuring the packaging dimensions for the part. In that
case, you would post them to the Packaging Dimensions forum topic in centimeters.
The dimensions entry on the catalog change request form is to be used for adding
stud dimensions for width and length and brick dimensions for height to standard
parts that can be easily measured in those terms (such as bricks and plates).
|
|
Author: | cosmicray | Posted: | Mar 31, 2021 14:23 | Subject: | Dimensions of tires | Viewed: | 57 times | Topic: | Catalog | Status: | Open | |
|
| I would like to provide a Catalog dimension for
Plus the various part assemblies that include that tire. The change page suggests
that the numbers are in studs. Is this correct, or should I be entering in cm
?
According to my caliper the tire really does measure 30 x 30 x 14 mm.
When entering the dimensions for the assemblies, do I do that with the wheel
inserted in the tire, or with them side by side ? example
Nita Rae
|
|
Author: | jennnifer | Posted: | Mar 31, 2021 09:40 | Subject: | Re: where does this go in the catologue? | Viewed: | 31 times | Topic: | Catalog | |
|
| In Catalog, SurplusParts writes:
| I have this poster that i received with the VIP program from Lego when i purchased
the new Ghostbustern ECTO-1.
I wasn't sure where it goes in the catalogue. I looked in Gearosters for
it. I wasn't sure if that is where it goes?
If yes, i am happy to add to the catalogue if it is not already there.
Thanks
|
I don't see it in the catalog either. I would add it as: Gear, Poster. Check
to see if it has a 7 digit number code on it to use as the item number.
Jen
|
|
Author: | SurplusParts | Posted: | Mar 31, 2021 07:12 | Subject: | where does this go in the catologue? | Viewed: | 85 times | Topic: | Catalog | Status: | Open | |
|
| I have this poster that i received with the VIP program from Lego when i purchased
the new Ghostbustern ECTO-1.
I wasn't sure where it goes in the catalogue. I looked in Gearosters for
it. I wasn't sure if that is where it goes?
If yes, i am happy to add to the catalogue if it is not already there.
Thanks
|
|
|
Author: | starbeanie | Posted: | Mar 30, 2021 21:17 | Subject: | Re: Jek-14 sw475/sw475a | Viewed: | 37 times | Topic: | Catalog | |
|
| From an employee or out of the factory. Like this
Obviously not from a set.
In Catalog, davidschweer writes:
| In Catalog, Hygrotus writes:
I have one in my collection and have been confused for years. I have been searching
for information about it but have found none. I originally thought it was a
head to another minifigure completely but it pops up on bricklink under jek.
You have to piece him out and look up just his head but the white variant is
present.
https://www.bricklink.com/catalogPG.asp?P=3626cpb1012&colorID=1
Does anyone know any information on this head or where it came from?
|
|
|
Next Page: 5 More | 10 More | 25 More | 50 More | 100 More
|
|