| Redisplay Messages: Compact | Brief | All | Full Show Messages: All | Without Replies| Author: | The_Brick_Freak  | | Posted: | Oct 20, 2019 06:02 | | Subject: | Inventory Change Request for Set 75250-1 | | Viewed: | 19 times | | Topic: | Inventories Requests (Entry) | | Status: | Open | |
| Please make changes to the following inventory:
* Add 4 Part 2436b Dark Bluish Gray Bracket 1 x 2 - 1 x 4 with Rounded Corners (Alternate)
Comments from Submitter:
Tried to change from 2 rounded corner bracket (2436c) to all 4 corners rounded (2436b) and was rejected.
Can we at least add this as an alternate part? I parted 4x sets and this part was in all of them. There were no 2436c parts
|
 |
| Author: | The_Brick_Freak | | Posted: | Oct 19, 2019 05:05 | | Subject: | Inventory Change Request for Set 75250-1 | | Viewed: | 17 times | | Topic: | Inventories Requests (Entry) | | Status: | Open | |
| Please make changes to the following inventory:
* Change 4 Part Dark Bluish Gray {2436c Bracket 1 x 2 - 1 x 4 with Two Rounded Corners at the Bottom to 2436b Bracket 1 x 2 - 1 x 4 with Rounded Corners}
Comments from Submitter:
Change from 2 rounded corners to 4 rounded corners
|
| Author: | The_Brick_Freak | | Posted: | Jun 24, 2019 02:24 | | Subject: | Re: Tutorial | | Viewed: | 32 times | | Topic: | Inventories | |
| Thank You So much RecycledBrick, sent me a PM and gave me a quick run down and
some confidence to give it a go 
Thank You Again
|
|
| Author: | The_Brick_Freak | | Posted: | Jun 23, 2019 07:54 | | Subject: | Re: Tutorial | | Viewed: | 33 times | | Topic: | Inventories | |
| In Inventories, Brickwilbo writes:
| | In Inventories, The_Brick_Freak writes:
| | Hey peoples! i would really like to be able to contribute by adding New set inventories
into bricklink but i am worried i will make a mistake.
Is their a tutorial on how to do it correctly with a run down on how everything
works? If so, please point me to the video or link. If not is this something
a more experienced person might be interested in doing to teach us?
Cheers
James
|
As start here are the Helppages:
https://www.bricklink.com/help.asp?topicID=38
|
Yea i have read that article and it is somewhat helpful however i cant see where
it covers what to do if the part or minifig is new and not in the system. I have
seen some people put minifig parts and not whole minifigs into the inventory
and it doesnt really go into details about these sorts of things.
|
|
| Author: | The_Brick_Freak | | Posted: | Jun 23, 2019 06:30 | | Subject: | Tutorial | | Viewed: | 115 times | | Topic: | Inventories | | Status: | Open | |
| Hey peoples! i would really like to be able to contribute by adding New set inventories
into bricklink but i am worried i will make a mistake.
Is their a tutorial on how to do it correctly with a run down on how everything
works? If so, please point me to the video or link. If not is this something
a more experienced person might be interested in doing to teach us?
Cheers
James
|
| Author: | The_Brick_Freak | | Posted: | Jun 14, 2019 05:08 | | Subject: | Re: 70839 | | Viewed: | 41 times | | Topic: | Inventories | |
| In Inventories, Hygrotus writes:
| | In Inventories, The_Brick_Freak writes:
| | Thanks for the fast response axaday - I just need to hope Hygrotus sees this
message and can make it a priority haha
I would certainly give it a shot myself if i had more confidence in what to do
Regards
James
|
I will see what I can do
|
Woo Hoo - Thank You So Much
|
| Author: | The_Brick_Freak | | Posted: | Jun 13, 2019 00:48 | | Subject: | Re: 70839 | | Viewed: | 35 times | | Topic: | Inventories | |
| Thanks for the fast response axaday - I just need to hope Hygrotus sees this
message and can make it a priority haha
I would certainly give it a shot myself if i had more confidence in what to do
Regards
James
|
| Author: | The_Brick_Freak | | Posted: | Jun 12, 2019 21:34 | | Subject: | 70839 | | Viewed: | 85 times | | Topic: | Inventories | | Status: | Open | |
| Any idea when 70839 The Rexcelsior will be inventoried? been keeping an eye on
this one for a while, not sure if anyone had plans to get it done.
Thanks
|
|
|
