| Redisplay Messages: Compact | Brief | All | Full Show Messages: All | Without Replies Author: | Rick_S. | Posted: | Jun 24, 2020 20:29 | Subject: | Re: Changing rules of feedback | Viewed: | 48 times | Topic: | Suggestions | |
| In Suggestions, tEoS writes:
| Recheck the facts, then reread your full report of the incident. Then maybe
you will see the error.
In Suggestions, Rick_S. writes:
| In Suggestions, tEoS writes:
| Buyer left neutral feedback = error in what you wrote
| Actually there is no error, the synopsis is based on available data. but that
is just one incident it still brings up the issue that retaliatory feedback cannot
be removed and in that, it can cause more issues down the road. and it also prevents
buyers from leaving honest feedback in fear they will receive retaliatory feedback
in response.
|
|
Wrong again: it was negative, you notice the negative feedback they left for
Sludgemonster?
https://www.bricklink.com/feedback.asp?fdbType=2&p=mjsheller
and it seems this seller is pretty notorious in not being a great seller and
leaving retaliatory feedback too.
|
|
Yes buyer left neutral, but still does not excuse the negative left by the seller.
and the way the rules are written the seller could do nothing about it. since
the rules were very specific on what reasons feedback could be removed. and that
is what I want changed since they are not the only reasons, since retaliatory
feedback has been removed before and so forth. (in fact he has already contacted
the admins about getting the feedback removed)
|
|
Author: | M.Boss | Posted: | Jun 24, 2020 20:23 | Subject: | Re: Darth Vader Head Mold Variance | Viewed: | 22 times | Topic: | Catalog | |
| In Catalog, M.Boss writes:
|
When comparing two Darth Vader figures I had, I discovered a mold variance between
two helmets. The "old" type came likey was made from 1999-2014, while The "new"
type appeared in the 2019 20th Anniversary Clone Scout Walker I think
this new mold was created because in order to create the anniversary figure lego
wanted to use a 1 piece Vader helmet, as opposed to the 2 piece helmets they
switched to a couple of years ago. This mold variation deserves a note in the
catalog entry for the helmet,, or a variant added to the catalog, but I'm
not sure which. If someone wants to take the appropriate action from here, please
go ahead. See the attached image for the differences between the two.
|
Anyone? Does this mold change necessitate an amendment to the Bricklink Catalog?
|
|
Author: | tEoS | Posted: | Jun 24, 2020 20:11 | Subject: | Re: Changing rules of feedback | Viewed: | 33 times | Topic: | Suggestions | |
| Recheck the facts, then reread your full report of the incident. Then maybe
you will see the error.
In Suggestions, Rick_S. writes:
| In Suggestions, tEoS writes:
| Buyer left neutral feedback = error in what you wrote
| Actually there is no error, the synopsis is based on available data. but that
is just one incident it still brings up the issue that retaliatory feedback cannot
be removed and in that, it can cause more issues down the road. and it also prevents
buyers from leaving honest feedback in fear they will receive retaliatory feedback
in response.
|
|
Wrong again: it was negative, you notice the negative feedback they left for
Sludgemonster?
https://www.bricklink.com/feedback.asp?fdbType=2&p=mjsheller
and it seems this seller is pretty notorious in not being a great seller and
leaving retaliatory feedback too.
|
|
|
Author: | Hygrotus | Posted: | Jun 24, 2020 18:49 | Subject: | Re: How are stud measurements translated? | Viewed: | 46 times | Topic: | Catalog | |
| In Catalog, Crafteewon writes:
| Hello
I got a quote request from a customer saying that the shipping was too high.
When I looked at the order it looks like the below piece is the issue.
I have shipped this part before with no issues as lettermail.
With Canada post anything thicker than 2cm must be sent as parcel which is much
more expensive.
I am trying to understand how bricklink takes the 2x2x2 and translates that to
shipping dimensions in centimetres or inches.
Also can someone help me to understand how this can be 2x2x2 when one side is
longer than it is wide.
Is one of the measurements stacked bricks?
Thanks for any help
Edward
|
https://www.bricklink.com/help.asp?helpID=261
|
|
Author: | SylvainLS | Posted: | Jun 24, 2020 18:14 | Subject: | Re: Changing rules of feedback | Viewed: | 41 times | Topic: | Suggestions | |
| In Suggestions, Rick_S. writes:
| In Suggestions, SylvainLS writes:
| In Suggestions, Rick_S. writes:
| […]
ShakeyShuffle was a character.
|
But that doesn’t prevent a member using “ShackyShuffle” (with or without the
‘e’) for their ID here.
Are you Ricky Stratton from Silver Spoons?
|
Nope
|
Too bad. You wouldn’t gift me a million $ or two anyway?
|
Next Page: 5 More | 10 More | 25 More | 50 More | 100 More
|
|