| Redisplay Messages: Compact | Brief | All | Full Show Messages: All | Without Replies| Author: | randyf  | | Posted: | May 19, 2020 20:29 | | Subject: | Re: Inventory Change Request for Set 4669-1 | | Viewed: | 12 times | | Topic: | Inventories Requests | |
| In Inventories Requests, Tribols writes:
| | Please make changes to the following inventory:
* Add 2 Part 3678a Blue Slope 65 2 x 2 x 2 Smooth without Bottom Tube
Comments from Submitter:
The white 6140 is on a white 3004 block and the blue part it is on is not in the inventory!
|
Yes, the part is in the inventory. It is
This request will not be accepted.
Cheers,
Randy
|
|
 |
| Author: | Brixalotl | | Posted: | May 19, 2020 20:29 | | Subject: | Inventory Change Request for Set 75081-1 | | Viewed: | 21 times | | Topic: | Inventories Requests (Entry) | | Status: | Open | |
| Please make changes to the following inventory:
* Add 4 Part 44567a Black Hinge Plate 1 x 2 Locking with 1 Finger on Side with Bottom Groove (Alternate) (match ID 2)
* Change 4 Part Black 44567b Hinge Plate 1 x 2 Locking with 1 Finger on Side without Bottom Groove {match ID 0 to 2}
Comments from Submitter:
found variant during part out, thanks
|
|
| Author: | Brixalotl | | Posted: | May 19, 2020 19:43 | | Subject: | Inventory Change Request for Set 75918-1 | | Viewed: | 23 times | | Topic: | Inventories Requests (Entry) | | Status: | Open | |
| Please make changes to the following inventory:
* Change 4 Part Black {44567 Hinge Plate 1 x 2 Locking with 1 Finger on Side (Undetermined Type) to 44567a Hinge Plate 1 x 2 Locking with 1 Finger on Side with Bottom Groove}
Comments from Submitter:
confirmed during part out, thanks
|
|
| Author: | randyf | | Posted: | May 19, 2020 19:05 | | Subject: | Re: Inventory Change Request for Set 75234-1 | | Viewed: | 19 times | | Topic: | Inventories Requests | |
| In Inventories Requests, jamescanney writes:
| | Please make changes to the following inventory:
* Change {1 to 2} Part Black 2780 Technic, Pin with Friction Ridges Lengthwise with Center Slots (Extra)
Comments from Submitter:
i did the set twice and was left with 2 extra pins. With 55 used in the set, this would make more sense to have 2 extra included
|
I watched three speed builds from sealed set contents, and they all showed two
extra pins. Request accepted.
Cheers,
Randy
|
|
| Author: | Tribols | | Posted: | May 19, 2020 18:57 | | Subject: | Inventory Change Request for Set 4669-1 | | Viewed: | 18 times | | Topic: | Inventories Requests (Entry) | | Status: | Open | |
| Please make changes to the following inventory:
* Add 2 Part 3678a Blue Slope 65 2 x 2 x 2 Smooth without Bottom Tube
Comments from Submitter:
The white 6140 is on a white 3004 block and the blue part it is on is not in the inventory!
|
|
| Author: | Adjour | | Posted: | May 19, 2020 18:43 | | Subject: | Re: Technic Stickered Assembly Items | | Viewed: | 26 times | | Topic: | Inventories | |
| In Inventories, 1271moggy writes:
| | I have been checking my son's Technic collection for completeness etc, and
have come across some Technic stickered assembly items, which are not in the
catalogue under the counterparts section.
Is there a reason for this, or is it simply no-one has been brave enough to
do it?
I don't mind having a go and try and get them entered, but I am not very
good with coming up with good accurate descriptions for the stickers. If it
was a plain number, I'd be fine, but when it comes to a SW figure, I don't
wish to describe it as one thing and upset the SW fans who know it should be
something else.
Also is there a limit to the number of characters you can put into a description?
As some Technic entry's are quite long before anything else is added.
See the photos for the items which I am referring to.
Any help/advise I would be most grateful for.
|
I noticed when I was working on a similar project that yes, the counterparts
were missing to some of the older, smaller, technic sets.
I think just no one has bothered to work on it.
|
|
| Author: | randyf | | Posted: | May 19, 2020 18:20 | | Subject: | Re: Inventory Change Request for Set 3723-1 | | Viewed: | 23 times | | Topic: | Inventories Requests | |
| In Inventories Requests, dromeracer writes:
| | Please make changes to the following inventory:
* Change {11 to 7} Part Red 3010 Brick 1 x 4
* Change {4 to 2} Part Red 3701 Technic, Brick 1 x 4 with Holes
Comments from Submitter:
Checked with my own item of this type. But at these two position I have another qunantity as in the bricklink inventory. So I have checked the building instruction regadring these two item and so i have confirmed that the bricklink inventory have this two failures..
|
As has already been pointed out by another member, these parts were used to create
an alternate assembly of the connections of the arms to the body. These requests
will not be accepted.
Cheers,
Randy
|
|
| Author: | randyf | | Posted: | May 19, 2020 16:42 | | Subject: | Re: Inventory for fabac3 | | Viewed: | 32 times | | Topic: | Catalog | |
| In Catalog, Hygrotus writes:
Oops. My bad. Obviously I can't keep up with everything happening on the
catalog side of things like you can! 
|
|
|
| Author: | axaday | | Posted: | May 19, 2020 16:31 | | Subject: | Re: Three versions of the 9797 set | | Viewed: | 41 times | | Topic: | Catalog Requests | |
| In Catalog Requests, randyf writes:
| | Here is one of the most high profile cases of this:
|
I bought my 10030 a year after I decided to because I had to wait until I got
a bonus at work. It arrived in LBG. I had never seen LBG before and I hated
it.
I have gotten used to LBG by now. I do like LG better. But on the Star Destroyer,
LBG just isn't right.
|
Next Page: 5 More | 10 More | 25 More | 50 More | 100 More
|
|
