| Redisplay Messages: Compact | Brief | All | Full Show Messages: All | Without Replies| Author: | WFMTF  | | Posted: | Sep 15, 2018 09:07 | | Subject: | 3003 and 3003old | | Viewed: | 84 times | | Topic: | Inventories | | Status: | Open | |
| As far as I know none of the Trans- and Glittercolors have inside supports.
WHY do these colors appear as known colors on item 3003 and do not appear as
none colors on item 3003old - without inside supports.
This is a mismatch of catalog criterias - seen from my view.
I think that a short explanation in the additional notes would be good.
Thank you for a response
Waltraud
|
| Author: | odurt | | Posted: | Sep 9, 2018 12:17 | | Subject: | Note to be added for minifigre ac009 | | Viewed: | 65 times | | Topic: | Inventories | | Status: | Open | |
| Hi,
For the following minifigure, I have a 'c' style head.
Can you please add this note:
This minifigure has been found with both the 'b' and 'c' style
head.
as per
Thanks,
Sebastien
|
| Author: | Poppie123 | | Posted: | Sep 8, 2018 12:24 | | Subject: | SET 10765 | | Viewed: | 88 times | | Topic: | Inventories | | Status: | Open | |
| Hi There, Please can someone assist to auto part-out set 10765? Its not yet
available for part-out on Bricklink.
|
 |
| Author: | StormChaser | | Posted: | Sep 3, 2018 17:15 | | Subject: | Sources for Set Inventories | | Viewed: | 77 times | | Topic: | Inventories | | Status: | Open | |
| Since around February of this year we have been informally requiring that all
new inventories (meaning recent sets) be submitted from sealed set contents.
We believe this rule greatly reduces the error rate in inventories. If someone
has a brand new set in hand, then parts, part colors, part variants, and extras
can be more accurately determined.
The only concern was that the requirement would result in a reduction in inventories
being added. Fortunately, this has not occurred. There have been 580 sets released
so far this year and only 73 of those sets don't have inventories on BrickLink
(about 12.5%). We can always do better, but 87.5% of 2018 sets inventoried is
still pretty decent (especially considering what an improvement this is from
the past).
Therefore, we have decided to make this requirement a permanent rule for new
sets going forward. The way it works is this: if the set has been in the BrickLink
catalog less than one year, then the only source accepted for its inventory is
a sealed set. After that, any source is acceptable. You can see the new rule
here under the heading Source:
https://www.bricklink.com/help.asp?helpID=199
The only problem with this rule are sets like this:
We may consider listing these sets as exceptions to the rule, but for now they
are covered.
|
|
| Author: | StoreToys4Boys | | Posted: | Sep 1, 2018 14:37 | | Subject: | Inventory Pending Approval (?) | | Viewed: | 96 times | | Topic: | Inventories | | Status: | Open | |
| Can anybody can clarify why it take soo long for the inventory of a set to be
approve.
For doing sales,we need this inventory to be approve quickly.
Ex:75203 is been out for a month and other site have all inventory done.
I think with the sales amount that past here,we should expect a little bit of
service.
We are paying 3% on every sales and i think we should received a minimum of service.
Please don't reply its a voluntary work that user are doing the inventory.It
should not be voluntary first of all.This site is doing money.With the number
of set that coming out every month ,i think somebody should be payed and doing
this full time.
I just resign myself to spend a hour to enter and verify that set with brickstock.
|
|
| Author: | TyresOFlaherty | | Posted: | Aug 30, 2018 15:22 | | Subject: | Inventory for comcon057-1 | | Viewed: | 75 times | | Topic: | Inventories | | Status: | Open | |
| I have this set and wondered if I could help add inventory (and minifigs and
the "alternate" minifig"). Can someone point me in the right direction? I'm
quite good with graphics and would be more than happy to take clean photos of
the new elements/prints in this set.
Thanks!
|
| Author: | nectara | | Posted: | Aug 24, 2018 07:36 | | Subject: | 75203-1 | | Viewed: | 75 times | | Topic: | Inventories | | Status: | Open | |
| Hi
What's going on with 75203?
More than one month still ,,Inventory In Progress,,
Regards
Nectara
|
| Author: | CCBricks | | Posted: | Aug 21, 2018 21:44 | | Subject: | Parts for Gear #853191 | | Viewed: | 56 times | | Topic: | Inventories | | Status: | Open | |
| Evening All...
I cam across a particular head piece that is associated with Jack Sparrow that
is only in this item:
It shows no inventories for the figures. Are the figures glued together, or
is it just the brick bases? I might have the other parts for this particular
version of Sparrow, but I'd have to check my "odd ball" bin lol.
Brian
|
|
| Author: | tmxbricks | | Posted: | Aug 21, 2018 06:46 | | Subject: | Stickerd Parts no longer CPs? | | Viewed: | 94 times | | Topic: | Inventories | | Status: | Open | |
| Are stickered parts no longer being listed as counter parts in Bricklink inventories?
I was verifying some set inventories and noticed all the following sets have
no stickered parts as CPs:
41322
41323
41327
41328
41329
For my own purposes, I have put stickered parts in the comments section of Brickstock
as I verify my inventories, but I liked having them listed as CPs.
|
|
| Author: | WhiteVanMan | | Posted: | Aug 20, 2018 08:20 | | Subject: | Supplying a set's inventory | | Viewed: | 99 times | | Topic: | Inventories | | Status: | Open | |
| Hi all.
I've got 2 copies of a Duplo set that has not been inventoried.
I've tried to submit the inventory, and I apparently need to supply information
about a few parts that are not within the catalogue, but there IS information
about the parts as BrickLink is getting the data direct from LEGO
What do I need to do?
It's mostly the printed parts that I'm having issues with.
Please help as I can't sell the parts as the set isn't inventoried
regards,
Paul
|
Next Page: 5 More | 10 More | 25 More | 50 More | 100 More
|
|
