Discussion Forum: Thread 368830

 Author: Stuart9 View Messages Posted By Stuart9
 Posted: Apr 7, 2025 12:46
 Subject: Separating parts.
 Viewed: 138 times
 Topic: Suggestions
 Status:Open
 Vote:[Yes|No]
 Report:
Cancel Message
Cancel		Reply to Message
Reply
BrickLink
ID Card

Stuart9 (1456)

Location:  United Kingdom, England
Member Since Contact Type Status
Jul 22, 2012 Contact Member Seller
Buying Privileges - OKSelling Privileges - OK
Store Closed Store: Top Slot
Thought I’d ask if there is an easy way to separate parts 36010 & 36011.

Thanks.

 
Part No: 36010 Name: Ninjago Shaft Clip
* 		36010 Ninjago Shaft Clip
Parts: Human Tool

 
Part No: 36011 Name: Ninjago Wing / Sail Holder
* 		36011 Ninjago Wing / Sail Holder
Parts: Human Tool
 Author: Stuart9 View Messages Posted By Stuart9
 Posted: Apr 8, 2025 01:37
 Subject: Re: Separating parts.
 Viewed: 67 times
 Topic: Suggestions
 Report:
Cancel Message
Cancel		Reply to Message
Reply
BrickLink
ID Card

Stuart9 (1456)

Location:  United Kingdom, England
Member Since Contact Type Status
Jul 22, 2012 Contact Member Seller
Buying Privileges - OKSelling Privileges - OK
Store Closed Store: Top Slot
My suggestion is that this be added as an assembly as these two parts don’t seem
to be easily separated after they are assembled ?




In Suggestions, Stuart9 writes:
  Thought I’d ask if there is an easy way to separate parts 36010 & 36011.

Thanks.

 
Part No: 36010 Name: Ninjago Shaft Clip
* 		36010 Ninjago Shaft Clip
Parts: Human Tool

 
Part No: 36011 Name: Ninjago Wing / Sail Holder
* 		36011 Ninjago Wing / Sail Holder
Parts: Human Tool
 Author: Akir View Messages Posted By Akir
 Posted: Apr 8, 2025 16:30
 Subject: Re: Separating parts.
 Viewed: 42 times
 Topic: Suggestions
 Report:
Cancel Message
Cancel		Reply to Message
Reply
BrickLink
ID Card

Akir (202)

Location:  Austria, Steiermark
Member Since Contact Type Status
Dec 28, 2020 Contact Member Seller
Buying Privileges - OKSelling Privileges - OK
Store Closed Store: Some Old Bricks
In Suggestions, Stuart9 writes:
  My suggestion is that this be added as an assembly as these two parts don’t seem
to be easily separated after they are assembled ?




In Suggestions, Stuart9 writes:
  Thought I’d ask if there is an easy way to separate parts 36010 & 36011.

Thanks.

 
Part No: 36010 Name: Ninjago Shaft Clip
* 		36010 Ninjago Shaft Clip
Parts: Human Tool

 
Part No: 36011 Name: Ninjago Wing / Sail Holder
* 		36011 Ninjago Wing / Sail Holder
Parts: Human Tool


I have them, and I managed to disassemble them, but I can't remember how.
I think it was a matter of bending one of them in a certain way, and then the
other can be removed relatively easily. But I can't figure it out right now.
I think I looked it up on the net back then, and found instructions.
Sorry I can't be more helpful!
 Author: Stuart9 View Messages Posted By Stuart9
 Posted: Apr 8, 2025 17:51
 Subject: Re: Separating parts.
 Viewed: 50 times
 Topic: Suggestions
 Report:
Cancel Message
Cancel		Reply to Message
Reply
BrickLink
ID Card

Stuart9 (1456)

Location:  United Kingdom, England
Member Since Contact Type Status
Jul 22, 2012 Contact Member Seller
Buying Privileges - OKSelling Privileges - OK
Store Closed Store: Top Slot
Thanks for your reply, I’ll see if I can find a video.


In Suggestions, Akir writes:
  In Suggestions, Stuart9 writes:
  My suggestion is that this be added as an assembly as these two parts don’t seem
to be easily separated after they are assembled ?




In Suggestions, Stuart9 writes:
  Thought I’d ask if there is an easy way to separate parts 36010 & 36011.

Thanks.

 
Part No: 36010 Name: Ninjago Shaft Clip
* 		36010 Ninjago Shaft Clip
Parts: Human Tool

 
Part No: 36011 Name: Ninjago Wing / Sail Holder
* 		36011 Ninjago Wing / Sail Holder
Parts: Human Tool


I have them, and I managed to disassemble them, but I can't remember how.
I think it was a matter of bending one of them in a certain way, and then the
other can be removed relatively easily. But I can't figure it out right now.
I think I looked it up on the net back then, and found instructions.
Sorry I can't be more helpful!