Discussion Forum: Thread 269693 |
|
|
| | Author: | Mirko8710 | Posted: | Jun 12, 2020 09:27 | Subject: | Inventory Change Request for Minifig sh616 | Viewed: | 30 times | Topic: | Inventories Requests (Entry) | Status: | Open | |
|
| Please make changes to the following inventory:
* Add 4 Part 44302a Dark Bluish Gray Hinge Plate 1 x 2 Locking with 2 Fingers on End and 9 Teeth with Bottom Groove
Comments from Submitter:
I don't know how to add an alternate part for a minifigure. Another question: how can I add the counterpart of the four slope courved with stickers? Many thanks for all.
|
|
| | | | | |
| | | | Author: | Hygrotus | Posted: | Jun 12, 2020 09:33 | Subject: | Re: Inventory Change Request for Minifig sh616 | Viewed: | 25 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Mirko8710 writes:
| Please make changes to the following inventory:
* Add 4 Part 44302a Dark Bluish Gray Hinge Plate 1 x 2 Locking with 2 Fingers on End and 9 Teeth with Bottom Groove
Comments from Submitter:
I don't know how to add an alternate part for a minifigure. Another question: how can I add the counterpart of the four slope courved with stickers? Many thanks for all.
|
Minfigures can't have alternate parts. Only a note can be added that there
are two variants of this part in this minfigure
As for stickered and unsitckered variants of minfigures second entry should be
added.
Example
Sticered minfigures has 's' after number
|
|
|
| | | | | |
| | | | Author: | Hygrotus | Posted: | Jun 12, 2020 09:38 | Subject: | Re: Inventory Change Request for Minifig sh616 | Viewed: | 22 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Mirko8710 writes:
| Please make changes to the following inventory:
* Add 4 Part 44302a Dark Bluish Gray Hinge Plate 1 x 2 Locking with 2 Fingers on End and 9 Teeth with Bottom Groove
Comments from Submitter:
I don't know how to add an alternate part for a minifigure. Another question: how can I add the counterpart of the four slope courved with stickers? Many thanks for all.
|
So this request has been rejected a note to the minfigure has been added.
|
|
| | | | | | | | | |
| | | | | | Author: | axaday | Posted: | Jun 12, 2020 09:45 | Subject: | Re: Inventory Change Request for Minifig sh616 | Viewed: | 20 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Hygrotus writes:
| In Inventories Requests, Mirko8710 writes:
| Please make changes to the following inventory:
* Add 4 Part 44302a Dark Bluish Gray Hinge Plate 1 x 2 Locking with 2 Fingers on End and 9 Teeth with Bottom Groove
Comments from Submitter:
I don't know how to add an alternate part for a minifigure. Another question: how can I add the counterpart of the four slope courved with stickers? Many thanks for all.
|
So this request has been rejected a note to the minfigure has been added.
|
If it had been anyone other than the person who discovered the new piece, I would
think it wasn't really two versions.
|
|
|
| | | | | | | | | | | | | |
| | | | | | | | Author: | Hygrotus | Posted: | Jun 12, 2020 09:49 | Subject: | Re: Inventory Change Request for Minifig sh616 | Viewed: | 27 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, axaday writes:
| In Inventories Requests, Hygrotus writes:
| In Inventories Requests, Mirko8710 writes:
| Please make changes to the following inventory:
* Add 4 Part 44302a Dark Bluish Gray Hinge Plate 1 x 2 Locking with 2 Fingers on End and 9 Teeth with Bottom Groove
Comments from Submitter:
I don't know how to add an alternate part for a minifigure. Another question: how can I add the counterpart of the four slope courved with stickers? Many thanks for all.
|
So this request has been rejected a note to the minfigure has been added.
|
If it had been anyone other than the person who discovered the new piece, I would
think it wasn't really two versions.
|
Inventory of this set was made from Sealed Set Content by Stormchaser and there
are two DBG 44302b so it was logicall that this min figs would have the same
parts even it minfig by itself was inventoried from instruction but luckily
only 4 were used here and two are still in set inventory. So assumpsion was correct
that minfig will have the same variant as one currently in inventory from sealed
set content.
|
|
|
| | | | | | | | | | | | | | | | | |
| | | | | | | | | | Author: | randyf | Posted: | Jun 12, 2020 15:03 | Subject: | Re: Inventory Change Request for Minifig sh616 | Viewed: | 22 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Hygrotus writes:
| In Inventories Requests, axaday writes:
| In Inventories Requests, Hygrotus writes:
| In Inventories Requests, Mirko8710 writes:
| Please make changes to the following inventory:
* Add 4 Part 44302a Dark Bluish Gray Hinge Plate 1 x 2 Locking with 2 Fingers on End and 9 Teeth with Bottom Groove
Comments from Submitter:
I don't know how to add an alternate part for a minifigure. Another question: how can I add the counterpart of the four slope courved with stickers? Many thanks for all.
|
So this request has been rejected a note to the minfigure has been added.
|
If it had been anyone other than the person who discovered the new piece, I would
think it wasn't really two versions.
|
Inventory of this set was made from Sealed Set Content by Stormchaser and there
are two DBG 44302b so it was logicall that this min figs would have the same
parts even it minfig by itself was inventoried from instruction but luckily
only 4 were used here and two are still in set inventory. So assumpsion was correct
that minfig will have the same variant as one currently in inventory from sealed
set content.
|
The 'a' version should be the one listed in the inventory and minifigure
as the regular part, and the 'b' version should be the alternate part.
|
|
|
|
|
|
|