are 582mm x 378mm. Which is
the size of the Box itself (!)
How were these dimensions populated and what can I do to remove them altogether
(not just one by one)?
(Or better yet to mass-set the dimensions correctly.)
Thanhk you again.
LOL me again, and thank you for alerting me to this as well as I went back and
checked mine saw some of them had a base thickness of 1cm - this is wrong. Research
cap on and lo behold - I think there are still a few of these floating about:
https://www.bricklink.com/message.asp?ID=1063022
So that gets to the how it is populated. How to mass change it is another matter
altogether. Would you just want to change the thickness or do you want actual
dimensions? For actual dimensions you are going to have to measure each and every
one which still has the z dimension set to 10mm or 0mm. There is no way to simply
check this you have to check your entire inventory manually as there is no tool
to search the packing dimensions of items in your inventory. I'm not quite
sure if you can mass change the dimensions for your inventory - are they not
all different? Setting them all to manual for the time being, would be the same
method as in that other thread, except now you go M for Manual.
To mass change the dimensions:
For an item which you want to change the dimensions to say dim X, dim Y, dim
Z to 180 x 38 x 28 mm
Use the find and replace method in this message:
https://www.bricklink.com/message.asp?ID=1166531
You make the file as you would upload it and add the lines as follows: (put angle
brackets where I have now got square brackets)
As I noted - you anyway have to punch in values for each one. It might be easier
to set them all to manual, have some unfortunae soul sit with a caliper for a
day and ask for mass update on this topic:
https://www.bricklink.com/message.asp?ID=1059042
then reset your invetory again. It normally takes about a day for these to be
fixed, but since Russell is the only doing all of this now, I would suggest giving
a bit of extra time.
I'm also going to apologise here, I've never thought of checking those
dmension when I submit items for the catalogue. My bad. I will make a big fat
note to fix this oversight on my part, thank you again for pointing me in the
right direction.
are 582mm x 378mm. Which is
the size of the Box itself (!)
How were these dimensions populated and what can I do to remove them altogether
(not just one by one)?
(Or better yet to mass-set the dimensions correctly.)
Thanhk you again.
LOL me again, and thank you for alerting me to this as well as I went back and
checked mine saw some of them had a base thickness of 1cm - this is wrong. Research
cap on and lo behold - I think there are still a few of these floating about:
https://www.bricklink.com/message.asp?ID=1063022
So that gets to the how it is populated. How to mass change it is another matter
altogether. Would you just want to change the thickness or do you want actual
dimensions? For actual dimensions you are going to have to measure each and every
one which still has the z dimension set to 10mm or 0mm. There is no way to simply
check this you have to check your entire inventory manually as there is no tool
to search the packing dimensions of items in your inventory. I'm not quite
sure if you can mass change the dimensions for your inventory - are they not
all different? Setting them all to manual for the time being, would be the same
method as in that other thread, except now you go M for Manual.
To mass change the dimensions:
For an item which you want to change the dimensions to say dim X, dim Y, dim
Z to 180 x 38 x 28 mm
Use the find and replace method in this message:
https://www.bricklink.com/message.asp?ID=1166531
You make the file as you would upload it and add the lines as follows: (put angle
brackets where I have now got square brackets)
As I noted - you anyway have to punch in values for each one. It might be easier
to set them all to manual, have some unfortunae soul sit with a caliper for a
day and ask for mass update on this topic:
https://www.bricklink.com/message.asp?ID=1059042
then reset your invetory again. It normally takes about a day for these to be
fixed, but since Russell is the only doing all of this now, I would suggest giving
a bit of extra time.
I'm also going to apologise here, I've never thought of checking those
dmension when I submit items for the catalogue. My bad. I will make a big fat
note to fix this oversight on my part, thank you again for pointing me in the
right direction.
HTH
Wonderful, Jean!
Between BrickStock and Notepad, it worked.
I changed every Instructions to Weight Bound and the Dimensions to 300x200x10mm
(A4 size). It works here because as long as it is under the 90cm linear measure,
only the weight counts for shipping rates.
(Will have to adjust the bigger ones A3 size manually, but they're only a
few.)
Thank you again for your detailed explanation!
I will be uploading many Instructions this year, hopefully I can enter the correct
dimensions to the Catalog whenever Catalog Changes are working again.
Portugal
South Africa
