white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
Robert
Hi Robert - I thought there was all this talk and discussion about assemblies
a short time ago and that has changed but I will bow to your knowledge and separate
them out.
white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
Robert
Hi Robert - I thought there was all this talk and discussion about assemblies
a short time ago and that has changed but I will bow to your knowledge and separate
them out.
Not sure about that discussion but thinking about it the picture may confuse
some buyers into thinking they get 2 halves when ordering 1.. so I'm going
to make that clear in our description.
white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
Robert
Hi Robert - I thought there was all this talk and discussion about assemblies
a short time ago and that has changed but I will bow to your knowledge and separate
them out.
Not sure about that discussion but thinking about it the picture may confuse
some buyers into thinking they get 2 halves when ordering 1.. so I'm going
to make that clear in our description.
Robert
I've added a Lego render showing just the one part to avoid confusion. You
may need to do a hard refresh to see the new image.
white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly
Maybe add a simple line in the picture to show it’s both sides of the same part
and not two parts.
and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
white rubber band which holds the two halves
together. The instructions show the rubber band being used in each case. Should
there be an inventory for the part?
As currently set up in the catalogue 29112pb01 is for 1 piece i.e. half of the
assembly and the band is just another separate part. For an assembly the inventory
would need to be 2 x 29112pb01 plus one band but typically assemblies like this
are not catalogued.
Robert
This one is:
*
15073c01 (Inv) Rock Boulder Hinged with White Rubber Belt Small (15073 / x71) Parts: Rock
What are the guidelines that the venus flytrap is not an assembly? It is really
confusing.
What are the guidelines that the venus flytrap is not an assembly? It is really
confusing.
At this moment there are little to no guidelines on what should or should not
be added to the catalog as an assembly. The current part entry for the flytrap
is not an assembly because it is an entry for just one shell (you'd need
two shells plus a couple other parts for a complete assembly).
As for whether the catalog would accept an entry for the complete assembly if
someone submitted it with a photo . . . well, there are no rules. Assemblies
are something which need to be addressed in writing, but which haven't yet
been.
United Kingdom, England
USA, California
France, Nouvelle-Aquitaine
Netherlands, Zuid-Holland
