Discussion Forum: Thread 291219 |
|
|
| | Author: | Gandalf68 | Posted: | Jun 11, 2021 08:21 | Subject: | Retro-engineering problem (Part 3) | Viewed: | 88 times | Topic: | Help | |
|
| Here is another picture where i have trouble identifiyng parts :
I'm pretty sure that the Grey part is a "Tile, Round 2x2 with open stud (18674)",
but is the Trans-Clear part on top of it a "Dish 2x2 inverted (4740)" ?
Because in Studio, the whole thing seems too small in comparison (and a Dish
3x3 is too large)
Any thoughts ?
|
|
|
| | | | | |
| | | | Author: | tons_of_bricks | Posted: | Jun 11, 2021 08:23 | Subject: | Re: Retro-engineering problem (Part 3) | Viewed: | 25 times | Topic: | Help | |
|
| In Help, Gandalf68 writes:
| Here is another picture where i have trouble identifiyng parts :
I'm pretty sure that the Grey part is a "Tile, Round 2x2 with open stud (18674)",
but is the Trans-Clear part on top of it a "Dish 2x2 inverted (4740)" ?
Because in Studio, the whole thing seems too small in comparison (and a Dish
3x3 is too large)
Any thoughts ?
|
That doesn't look like a tile round, almost like a 3x3 dish facing the other
way.
|
|
| | | | | | | | | |
| | | | | | Author: | Gandalf68 | Posted: | Jun 11, 2021 08:32 | Subject: | Re: Retro-engineering problem (Part 3) | Viewed: | 28 times | Topic: | Help | |
|
| In Help, firestar246 writes:
| In Help, Gandalf68 writes:
| Here is another picture where i have trouble identifiyng parts :
I'm pretty sure that the Grey part is a "Tile, Round 2x2 with open stud (18674)",
but is the Trans-Clear part on top of it a "Dish 2x2 inverted (4740)" ?
Because in Studio, the whole thing seems too small in comparison (and a Dish
3x3 is too large)
Any thoughts ?
|
That doesn't look like a tile round, almost like a 3x3 dish facing the other
way.
|
I'm not sure because it's looks flat, and besides, a 3x3 Dish would cover
the whole section underneath because i'ts 3 studs long
|
|
| | | | | |
| | | | Author: | starbeanie | Posted: | Jun 11, 2021 08:27 | Subject: | Re: Retro-engineering problem (Part 3) | Viewed: | 31 times | Topic: | Help | |
|
|
In Help, Gandalf68 writes:
| Here is another picture where i have trouble identifiyng parts :
I'm pretty sure that the Grey part is a "Tile, Round 2x2 with open stud (18674)",
but is the Trans-Clear part on top of it a "Dish 2x2 inverted (4740)" ?
Because in Studio, the whole thing seems too small in comparison (and a Dish
3x3 is too large)
Any thoughts ?
|
|
|
| | | | | |
| | | | Author: | MrPetovan | Posted: | Jun 11, 2021 08:28 | Subject: | Re: Retro-engineering problem (Part 3) | Viewed: | 39 times | Topic: | Help | |
|
| This is a
and a
In Help, Gandalf68 writes:
| Here is another picture where i have trouble identifiyng parts :
I'm pretty sure that the Grey part is a "Tile, Round 2x2 with open stud (18674)",
but is the Trans-Clear part on top of it a "Dish 2x2 inverted (4740)" ?
Because in Studio, the whole thing seems too small in comparison (and a Dish
3x3 is too large)
Any thoughts ?
|
|
|
| | | | | | | | | |
| | | | | | Author: | Gandalf68 | Posted: | Jun 11, 2021 08:38 | Subject: | Re: Retro-engineering problem (Part 3) | Viewed: | 35 times | Topic: | Help | |
|
| In Help, MrPetovan writes:
| This is a
and a
In Help, Gandalf68 writes:
| Here is another picture where i have trouble identifiyng parts :
I'm pretty sure that the Grey part is a "Tile, Round 2x2 with open stud (18674)",
but is the Trans-Clear part on top of it a "Dish 2x2 inverted (4740)" ?
Because in Studio, the whole thing seems too small in comparison (and a Dish
3x3 is too large)
Any thoughts ?
|
|
Yes !
You're right MrPetovan and starbeanie
Thanks a lot !
|
|
|
|
|
|