Discussion Forum: Thread 288575

 Author: danielestarkey View Messages Posted By danielestarkey
 Posted: Apr 22, 2021 05:30
 Subject: Inventory Change Request for Set 8692-1
 Viewed: 29 times
 Topic: Inventories Requests (Entry)
 Status:Open
Cancel Message
Cancel
Reply to Message
Reply
BrickLink
ID Card

danielestarkey (61)

Location:  United Kingdom, Wales
Member Since Contact Type Status
Mar 24, 2021 Contact Member Seller
Buying Privileges - OKSelling Privileges - OK
Store Closed Store: DanstaBricks
Please make changes to the following inventory:
 
Set No: 8692  Name: Vamprah
* 
8692-1 (Inv) Vamprah
48 Parts, 2008
Sets: BIONICLE: Phantoka

* Delete 2 Part 50898 Black Technic, Axle and Pin Connector 2 x 7 with Two Ball Joint Sockets (match ID 1)
* Add 2 Part 61054 Black Technic, Axle and Pin Connector 2 x 7 with Two Ball Joint Sockets, Squared Ends

Comments from Submitter:
Part 61054 should be the in the main list of pieces, not an alternate item, as from 2008 onwards, all Bionicle axle and pin connectors had squared ends. Therefore, part 50898 should be removed from the inventory.
 Author: randyf View Messages Posted By randyf
 Posted: Oct 28, 2022 16:39
 Subject: Re: Inventory Change Request for Set 8692-1
 Viewed: 21 times
 Topic: Inventories Requests
Cancel Message
Cancel
Reply to Message
Reply
BrickLink
ID Card

randyf (442)

Location:  USA, Ohio
Member Since Contact Type Status
Sep 16, 2009 Member Does Not Allow Contact Seller
Buying Privileges - OKSelling Privileges - OK
Store Closed Store: The Bricking Spectre
BrickLink Catalog Administrator (?)
In Inventories Requests, danielestarkey writes:
  Please make changes to the following inventory:
 
Set No: 8692  Name: Vamprah
* 
8692-1 (Inv) Vamprah
48 Parts, 2008
Sets: BIONICLE: Phantoka

* Delete 2 Part 50898 Black Technic, Axle and Pin Connector 2 x 7 with Two Ball Joint Sockets (match ID 1)
* Add 2 Part 61054 Black Technic, Axle and Pin Connector 2 x 7 with Two Ball Joint Sockets, Squared Ends

Comments from Submitter:
Part 61054 should be the in the main list of pieces, not an alternate item, as from 2008 onwards, all Bionicle axle and pin connectors had squared ends. Therefore, part 50898 should be removed from the inventory.


There is not a ton of good evidence out there to look at in regards to this change
request, but what I have seen never shows part 50898 in the set. I have not even
seen one used set that includes it, and I have looked at a lot of them.

The best evidence that I have are photographs on Brickshelf that have timestamps
from early and mid 2008 that clearly show 61054. Since the set was released in
early 2008, these photos are almost surely from original sets.

Also, because the original inventory was inventoried from "Instructions" as its
source, it should have been inventoried with 61054 from the very beginning. The
instructions clearly show 61054 in the build and the parts list.

The inventory was then later confirmed from "Sealed Set Contents" with the addition
of the alternate.

In conclusion, I find it very unlikely that this set ever came with 50898, and
it can always be added back if any "sure thing" evidence pops up that it did.

These requests have been accepted.

Cheers,
Randy

P.S. I believe some of the other Phantoka sets may have a similar issue here,
but I don't have the time to look over all of them right now.