* Add 2 Part 3024 Yellow Plate 1 x 1
* Add 1 Part 3794a Yellow Plate, Modified 1 x 2 with 1 Stud without Groove (Jumper)
* Change {1 to 2} Part Red 3069b Tile 1 x 2 with Groove
Comments from Submitter:
I got a used copy in very good condition. Even the sprues are there. These parts were extra in the box. I found almost all of them on the models on back of the box.
* Add 2 Part 3024 Yellow Plate 1 x 1
* Add 1 Part 3794a Yellow Plate, Modified 1 x 2 with 1 Stud without Groove (Jumper)
* Change {1 to 2} Part Red 3069b Tile 1 x 2 with Groove
Comments from Submitter:
I got a used copy in very good condition. Even the sprues are there. These parts were extra in the box. I found almost all of them on the models on back of the box.
- The yellow jumper can be seen in two models.
- Two yellow 1*1 plate can be seen on the ship (left-side top) Sorry for the
quality of the image. The yellow plates 4*1, 1*1 and 10*1 are used on each side
of the ship, on the edge.
- Two 1*2 red tiles are used on various red or yellow motorcycles.
- It is likely that on the bottom left-side of model, three yellow 1*1 plates
are used. But the box art is not clear.
I believe three yellow plates 1*1 came with this set. Whether the third is extra
is used on an alternate model is not clear.
* Add 2 Part 3024 Yellow Plate 1 x 1
* Add 1 Part 3794a Yellow Plate, Modified 1 x 2 with 1 Stud without Groove (Jumper)
* Change {1 to 2} Part Red 3069b Tile 1 x 2 with Groove
Comments from Submitter:
I got a used copy in very good condition. Even the sprues are there. These parts were extra in the box. I found almost all of them on the models on back of the box.
- The yellow jumper can be seen in two models.
- Two yellow 1*1 plate can be seen on the ship (left-side top) Sorry for the
quality of the image. The yellow plates 4*1, 1*1 and 10*1 are used on each side
of the ship, on the edge.
- Two 1*2 red tiles are used on various red or yellow motorcycles.
- It is likely that on the bottom left-side of model, three yellow 1*1 plates
are used. But the box art is not clear.
I believe three yellow plates 1*1 came with this set. Whether the third is extra
is used on an alternate model is not clear.
* Add 2 Part 3024 Yellow Plate 1 x 1
* Add 1 Part 3794a Yellow Plate, Modified 1 x 2 with 1 Stud without Groove (Jumper)
* Change {1 to 2} Part Red 3069b Tile 1 x 2 with Groove
Comments from Submitter:
I got a used copy in very good condition. Even the sprues are there. These parts were extra in the box. I found almost all of them on the models on back of the box.
- The yellow jumper can be seen in two models.
- Two yellow 1*1 plate can be seen on the ship (left-side top) Sorry for the
quality of the image. The yellow plates 4*1, 1*1 and 10*1 are used on each side
of the ship, on the edge.
- Two 1*2 red tiles are used on various red or yellow motorcycles.
- It is likely that on the bottom left-side of model, three yellow 1*1 plates
are used. But the box art is not clear.
I believe three yellow plates 1*1 came with this set. Whether the third is extra
is used on an alternate model is not clear.
Based on your photos the presence of the red 3069b and yellow 3794a is clearly
visible in the alternate models. Can you post photos showing a bit more detail
of the alternate models where the yellow 3024 are used? It would probably be
a bit better visible if you posted close-ups of just those models instead of
the whole back of the box.
* Add 2 Part 3024 Yellow Plate 1 x 1
* Add 1 Part 3794a Yellow Plate, Modified 1 x 2 with 1 Stud without Groove (Jumper)
* Change {1 to 2} Part Red 3069b Tile 1 x 2 with Groove
Comments from Submitter:
I got a used copy in very good condition. Even the sprues are there. These parts were extra in the box. I found almost all of them on the models on back of the box.
- The yellow jumper can be seen in two models.
- Two yellow 1*1 plate can be seen on the ship (left-side top) Sorry for the
quality of the image. The yellow plates 4*1, 1*1 and 10*1 are used on each side
of the ship, on the edge.
- Two 1*2 red tiles are used on various red or yellow motorcycles.
- It is likely that on the bottom left-side of model, three yellow 1*1 plates
are used. But the box art is not clear.
I believe three yellow plates 1*1 came with this set. Whether the third is extra
is used on an alternate model is not clear.
Based on your photos the presence of the red 3069b and yellow 3794a is clearly
visible in the alternate models. Can you post photos showing a bit more detail
of the alternate models where the yellow 3024 are used? It would probably be
a bit better visible if you posted close-ups of just those models instead of
the whole back of the box.
* Add 2 Part 3024 Yellow Plate 1 x 1
* Add 1 Part 3794a Yellow Plate, Modified 1 x 2 with 1 Stud without Groove (Jumper)
* Change {1 to 2} Part Red 3069b Tile 1 x 2 with Groove
Comments from Submitter:
I got a used copy in very good condition. Even the sprues are there. These parts were extra in the box. I found almost all of them on the models on back of the box.
- The yellow jumper can be seen in two models.
- Two yellow 1*1 plate can be seen on the ship (left-side top) Sorry for the
quality of the image. The yellow plates 4*1, 1*1 and 10*1 are used on each side
of the ship, on the edge.
- Two 1*2 red tiles are used on various red or yellow motorcycles.
- It is likely that on the bottom left-side of model, three yellow 1*1 plates
are used. But the box art is not clear.
I believe three yellow plates 1*1 came with this set. Whether the third is extra
is used on an alternate model is not clear.
Based on your photos the presence of the red 3069b and yellow 3794a is clearly
visible in the alternate models. Can you post photos showing a bit more detail
of the alternate models where the yellow 3024 are used? It would probably be
a bit better visible if you posted close-ups of just those models instead of
the whole back of the box.
Still difficult to see on those photos. Unfortunately those box art photos were
not always very clear. But I think I recognize the 1x1 plates. So I'll accept
this request.