Discussion Forum: Thread 244032 |
|
|
| | Author: | Brixalotl | Posted: | Nov 5, 2018 17:30 | Subject: | Inventory Change Request for Set 76000-1 | Viewed: | 32 times | Topic: | Inventories Requests (Entry) | Status: | Open | |
|
| Please make changes to the following inventory:
* Add 1 Part 13608 Flat Silver Minifig, Weapon Space Ray Gun - Rounded Heat Diffusers (Alternate) (match ID 5)
* Add 2 Part 44301b Red Hinge Plate 1 x 2 Locking with 1 Finger On End without Bottom Groove (Alternate) (match ID 6)
* Change 1 Part Flat Silver 87993 Minifig, Weapon Space Ray Gun {match ID 0 to 5}
* Change 2 Part Red 44301 Hinge Plate 1 x 2 Locking with 1 Finger On End (undetermined type) {match ID 0 to 6}
Comments from Submitter:
confirmed variants during part out, thanks
|
|
| | | | | |
| | | | Author: | Hygrotus | Posted: | Nov 5, 2018 17:41 | Subject: | Re: Inventory Change Request for Set 76000-1 | Viewed: | 22 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Brixalotl writes:
| * Add 2 Part 44301b Red Hinge Plate 1 x 2 Locking with 1 Finger On End without Bottom Groove (Alternate) (match ID 6)
* Change 1 Part Flat Silver 87993 Minifig, Weapon Space Ray Gun {match ID 0 to 5}
* Change 2 Part Red 44301 Hinge Plate 1 x 2 Locking with 1 Finger On End (undetermined type) {match ID 0 to 6}
|
I wrote it today in other request, but I can repeat it
In this situation when only undetermine was in inventory and no related alternate
we can get rid off this undetermine. You checked variant from sealed set content.
In this situation we simply change undetermine to confirmed variant.
But just to make sure (you frequently adding both variants for these hinges)
I ask if you didn't have "a" variant during part out? Or is it mistake and
you wanted to change also unteremine to "a" and add "b" as alternate?
|
|
|
| | | | | | | | | |
| | | | | | Author: | Brixalotl | Posted: | Nov 6, 2018 02:21 | Subject: | Re: Inventory Change Request for Set 76000-1 | Viewed: | 21 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Hygrotus writes:
| In Inventories Requests, Brixalotl writes:
| * Add 2 Part 44301b Red Hinge Plate 1 x 2 Locking with 1 Finger On End without Bottom Groove (Alternate) (match ID 6)
* Change 1 Part Flat Silver 87993 Minifig, Weapon Space Ray Gun {match ID 0 to 5}
* Change 2 Part Red 44301 Hinge Plate 1 x 2 Locking with 1 Finger On End (undetermined type) {match ID 0 to 6}
|
I wrote it today in other request, but I can repeat it
In this situation when only undetermine was in inventory and no related alternate
we can get rid off this undetermine. You checked variant from sealed set content.
In this situation we simply change undetermine to confirmed variant.
But just to make sure (you frequently adding both variants for these hinges)
I ask if you didn't have "a" variant during part out? Or is it mistake and
you wanted to change also unteremine to "a" and add "b" as alternate?
|
Yes, I agree we can eliminate the undetermined variant as you said. I will do
that in the future. Also, you are correct that I only found the "b" variant
while doing this one.
Thanks,
Jim
|
|
|
| | | | | | | | | | | | | |
| | | | | | | | Author: | Hygrotus | Posted: | Nov 6, 2018 02:22 | Subject: | Re: Inventory Change Request for Set 76000-1 | Viewed: | 23 times | Topic: | Inventories Requests | |
|
| In Inventories Requests, Brixalotl writes:
| In Inventories Requests, Hygrotus writes:
| In Inventories Requests, Brixalotl writes:
| * Add 2 Part 44301b Red Hinge Plate 1 x 2 Locking with 1 Finger On End without Bottom Groove (Alternate) (match ID 6)
* Change 1 Part Flat Silver 87993 Minifig, Weapon Space Ray Gun {match ID 0 to 5}
* Change 2 Part Red 44301 Hinge Plate 1 x 2 Locking with 1 Finger On End (undetermined type) {match ID 0 to 6}
|
I wrote it today in other request, but I can repeat it
In this situation when only undetermine was in inventory and no related alternate
we can get rid off this undetermine. You checked variant from sealed set content.
In this situation we simply change undetermine to confirmed variant.
But just to make sure (you frequently adding both variants for these hinges)
I ask if you didn't have "a" variant during part out? Or is it mistake and
you wanted to change also unteremine to "a" and add "b" as alternate?
|
Yes, I agree we can eliminate the undetermined variant as you said. I will do
that in the future. Also, you are correct that I only found the "b" variant
while doing this one.
Thanks,
Jim
|
Thanks for info. I will adjust it after approving.
|
|
|
|
|
|
|